SET YOUR CAR
TALK TO A PARTS EXPERT
- Exhausts
- Cat Back Exhaust System
- Downpipes And Y-pipes
- Exhaust Headers And Manifolds
- Exhaust Gaskets And Hardware
- Axle Back Exhausts
- Shop All
- Engine Management
- Plug And Play Engine Management
- Staged Power Packages
- Engine Management Sensors
- Stand Alone Engine Management
- Engine Management Harnesses
- Shop All
- Air Induction
- Short Ram Air Intakes
- Turbo Inlet Hoses And Pipes
- Cold Air Intakes
- Air Intake And Maf Hoses
- High Flow Replacement Panel Filters
- Shop All
Product images
Product Media
Community Media
PERRIN Turbo Inlet Hose 3in Black
Subaru WRX 2002-2007 / STI 2004+ / Forester XT 2004-2008
Features & Product Details
RallySport Direct carries a great selection of aftermarket upgrades brought to you by PERRIN Performance.
The PERRIN Turbo Inlet Hose has been designed to be a direct replacement for your factory inlet hose which is prone to failure after years or mileage of use. Usually, the stock turbo inlet will tear at the connection side of the turbocharger which can affect performance, throw a check engine light, and even reduce the power. PERRIN relieves this issue with its robust example.
DETAILS:
Specifications
Brand:
PERRIN
Color:
Black
Installation Hardware Included:
Yes
Layers:
4
Material:
Reinforced Silicone
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
PEOPLE WHO VIEWED THIS ITEM ALSO VIEWED
REVIEWS & CUSTOMER MEDIA
Customer Photos and Videos
5out of
5stars
Snoshado
First of all, this inlet fits perfectly... but is extremely hard to install. If you're brave enough to install a stock location turbo with a 3" inlet, you should already expect to have a hard time with your entire setup. You'll need to take your intake off and I recommend phenolic spacers to give you a little extra room.
1 of 1 people found the following review helpful
4out of
5stars
Criisharo
Everything mates up properly, strong material that wont fall apart but super tight fit. Some areas will be squished but I didn't notice any issues caused by this. It's the only 3in on the market but it works and hasn't caused any issues 4000 miles later. When I installed this I installed TGV's as well, I would assume the manifold would have to be to be removed for install due to sizing.
5out of
5stars
Schnitzel
Came with everything I needed to install it and seems like good quality. It fit my 2013 WRX with the the plastic manifold without issue. It fit rite up to a dominator 4.0 turbo fairly easily. I deleted the TGV, EGR, and all the air pump plumbing, wich may cause an issue with fitment. Something to keep in mind if you want to pair this intake with the plastic WRX manifold.
0 of 1 people found the following review helpful
2out of
5stars
stefantkd131970
I was running a 3 inch to 2 1/2 inch coupler and a ebay silicone inlet before i bought this. can honestly say that my old set up was better because the perrin pipe doesn't really let me run a bov hose.. its too close to the manifold and the silicone won't fit over my FP green inlet because its too thick in the rh corner and won't really slip on all the way.. installation is pretty easy if you face the nipple down the whole way in. Not bad but definitely not worth more than like 75 bucks.
4out of
5stars
mark29686
Good product, well made. Fitting it was a challenge requiring allot of effort but worth it in the end. The connecting pipework (clips and small hoses) should also be checked/changed before commencing the hose swop.
QUESTIONS & ANSWERS
-
Q: Fitment 2019 STI Gavan213 years ago
OEM turbo inlet has a fourth port towards the center of inlet close to the turbo. Why does this product only show three ports for hose hook ups? Will there just be an open line with no connection point with this new unit?
-
-
0 of
0 people found the
following answer helpful
A: The PCV diagnosis connector (that 4th port) will not be reused when installing this turbo inlet. The included instructions will walk you through disabling this connector.
Lane H. @ RallySport Direct 2 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Difference between this and PSP-INT-401BK Kellen Morse3 years ago
-
-
0 of
0 people found the
following answer helpful
A: This one is specific for large turbo's with 3inch inlets, where the PSP-INT-401BK will work with your stock turbo or turbo's with the stock sized 2.4inch inlet. Hope this helps!
Rick C. @ RallySport Direct 3 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: fitment 08 legacy spec B hunt4 years ago
-
-
0 of
0 people found the
following answer helpful
A: To determine accuracy, please contact our Customer Service.
Michael N.Was this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Stock Airbox teppey6 years ago
-
-
0 of
0 people found the
following answer helpful
A: The turbo inlet hose does not connect to the airbox and would be attached to the turbo on one end, and connects up with the air intake section before the MAF housing, before the airbox.
Brady R @ RallySport Direct 6 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: perrin 3" turbo inlet hose tony2tone7 years ago
-
-
0 of
0 people found the
following answer helpful
A: We wouldn't be able to confirm if the Perrin will stretch enough to fit, this is confirmed for 3" turbo inlets.
Nick S. @ RallySport Direct 7 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
