
Torque Solution Clutch Master Brace
Subaru WRX/STI 2008-2014
Features & Product Details
RallySport Direct proudly carries a massive selection of high-performance engine, suspension, and drivetrain upgrades to reinforce your race car, rally car, or overlander brought to you by Torque Solution.
Here, you are looking at the Torque Solution Clutch Master Brace. This brace has been designed to address the weak factory OEM pedal assembly spot welds which can break and lead to a sloppy pedal and clutch engagement. This brace will reinforce the clutch master cylinder to provide the driver with better feedback, and a more solid pedal feel.
DETAILS:
Specifications
PEOPLE WHO VIEWED THIS ITEM ALSO VIEWED
REVIEWS & CUSTOMER MEDIA

I had total failure of my clutch master due to most of the firewall spot welds breaking (ACT heavy duty clutch). The firewall failure also caused my pedal assembly to crack in multiple places. Replaced the master and braced it with this; along with a slew of other repairs to prevent this failure in the future. Humble Rumble firewall fasteners, a complete OEM pedal assembly also braced with the ITS pedal bracket. I highly recommend utilizing all of these to repair and brace your setup. Even with the ACT heavy duty clutch, there is almost zero firewall flex now. It did take a lot of time and effort to repair properly. But I am certain now that this will not happen again in the future.
The mount is one solid piece of machined aluminum and it looks great. It does modify the clutch master cylinders flex point to somewhere closer to the center of the firewall and it does firm up the pedal slightly. I imagine after I replace my clutch I'll notice the change even more. I was intimidated by the reviews taking about how difficult it was to install... It wasn't. Circuit Motorsports makes an almost identical brace and they have excellent install instructions on their site. I linked that below: https://www.importimageracing.com/products/crs-cms-drv-001bk-circuit-motorsports-clutch-master-cylinder-brace-subaru-wrx-sti-2008-2014 If you purchase this I would also recommend replacing the OEM Stop Pitch. During installation since you're going to have to remove and replace the bushing bolt that mounts the Stop Pitch to the firewall. The OEM Stop Pitch is a break point waiting to happen.
This is overall a great product and makes clutch engagement so much easier. Installed it while putting in the Grimmspeed Race Version Pitch Stop Mount. This was a bitch to put in due to the cylinder being hard to get those 10mm bolts off to slide this in. Instructions were not given to me and I looked online to see if their website provided instructions but they did not.
Install was pretty easy. I installed this along with a new pitch-stop brace. Clutch pedal feels a bit firmer and more predictable, helped the firewall flex too. I guess my only gripe is that it seems a bit pricey for what you get.
QUESTIONS & ANSWERS
-
Q: Any pictures? tyboscoops400792 years ago
I am curious where this mounts, are there any pictures of it installed?
-
-
0 of
0 people found the
following answer helpful
A: There is an installed photo listed from a customer review.
Lane H. @ RallySport Direct 2 years ago
-
0 of
0 people found the
following answer helpful
-
Q: Instructions? JayTV10272 years ago
Where are the instructions??? I feel like I did it wrong. The bolt that you slide through the back part of the Pitch Mount is very long and idk if it’s supposed to poke out a bit or a lot???
-
-
0 of
0 people found the
following answer helpful
A: We don't have any install instructions unfortunately, but a customer review does have an installed photo, and you can see his bolt sticking out pretty far from his pitch stop mount.
Lane H. @ RallySport Direct 2 years ago
-
0 of
0 people found the
following answer helpful
-
Q: RHD Kelford3 years ago
Does this fit right hand drive car?
-
-
0 of
0 people found the
following answer helpful
A: Unfortunately I cannot confirm fitment as we have not tested these on the RHD cars
Tylo R @ RallySport Direct
-
0 of
0 people found the
following answer helpful
-
Q: Fitment ‘10WRXTritton 3 years ago
I noticed this said for clutch master cylinder brace but will this also work with the grimmspeed brake master cylinder brace that bolts to the strut tower?
-
-
1 of
1 people found the
following answer helpful
A: Yes, they install in different locations and can be used together.
Marcus E. @ RallySport Direct 3 years ago
-
1 of
1 people found the
following answer helpful