- Exhausts
- Cat Back Exhaust System
- Downpipes And Y-pipes
- Exhaust Headers And Manifolds
- Exhaust Gaskets And Hardware
- Axle Back Exhausts
- Shop All
- Engine Management
- Plug And Play Engine Management
- Staged Power Packages
- Engine Management Sensors
- Stand Alone Engine Management
- Engine Management Harnesses
- Shop All
- Air Induction
- Short Ram Air Intakes
- Turbo Inlet Hoses And Pipes
- Cold Air Intakes
- Air Intake And Maf Hoses
- High Flow Replacement Panel Filters
- Shop All
-
Q: Pressure plate to fly Julian B3 years ago
Will this pressure plate line up with a stock 2009 wrx flywheel?
-
-
0 of
0 people found the
following answer helpful
A: We can only confirm this pressure plate to fit ACT's flywheel.
Brady R @ RallySport Direct 3 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: ACT 6 puck clutch CoochieSnatch693 years ago
-
-
0 of
0 people found the
following answer helpful
A: Certain clutch makers, including ACT, will have variances in pressure plate and flywheel diameter on certain kits. It's recommended to match this with ACT's flywheel to ensure proper fitment.
Marcus E. @ RallySport Direct 3 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Which Clutch JBauer2013WRX5 years ago
-
-
0 of
0 people found the
following answer helpful
A: It would depend on which turbo you were planning on going with, but this clutch would likely work well with your application. As a general rule though, puck clutches will be trickier to drive than a traditional full face.
Marcus E. @ RallySport Direct 5 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Will this clutch fit? jimbow917 years ago
-
-
0 of
0 people found the
following answer helpful
A: This clutch is confirmed to fit your 2010 2.5GT. I only recommend using this clutch on track/auto-x cars as it will be very harsh for everyday use on a street car. I recommend part # ACT SB5-HDSS for a street car.
Josh P. @ RallySport Direct 7 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: 2006 Forester XT CodyXT8 years ago
-
-
0 of
0 people found the
following answer helpful
A: If you use this clutch along with ACT 600480 it will work fine for your application.
Nick S. @ RallySport Direct 8 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: reverse? Stando8 years ago
-
-
0 of
0 people found the
following answer helpful
A: Puck style clutches are known to have rough engagement. This is amplified in reverse due to the straight cut reverse gear.
guest56ad69792a8d256e198b66b5 @Was this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Daily driver question rwbebe3096510 years ago
-
-
1 of
1 people found the
following answer helpful
A: This clutch is rated at 535 ft/lb of Torque at the crank so it will definitely be enough for your vehicle. In terms of driveability depending on which Stage 2 Exedy disc you are using this could be very similar in driveability for the street.
Nick S. @ RallySport Direct 10 years agoWas this answer helpful?
-
1 of
1 people found the
following answer helpful
-
Q: Run on stock flywheel smatney064149910 years ago
-
-
1 of
1 people found the
following answer helpful
A: Yes, on the WRX it would work on the OEM flywheel, however with a clutch this aggressive, I personally feel a lightweight flywheel would greatly compliment this clutch. Thanks.
Rick C. @ RallySport Direct 10 years agoWas this answer helpful?
-
1 of
1 people found the
following answer helpful
