SET YOUR CAR
FREE SHIPPING
On orders over $100
TALK TO A PARTS EXPERT
RALLYSPORT GUARANTEE
100% Money Back on Select Parts

ATI Center Gauge Pod

MODEL # ATIATI-CLUST-GEGH-60

$165.60


  • Q: 52 mm  aliciamiros627815 years ago

    I bought 3 52mm defis. Will they fit or do I need to buy step down rings separately?
    • 1 of 1 people found the following answer helpful

      A:  This pod out of the box will hold 60mm gauges. You will need ATI's Adapter Rings for your 52mm gauges, which you can find by searching Part # ATI 52/60-CONV-TRIO

      Brady R. @ RallySport Direct 5 years ago  
        
      Was this answer helpful?
  • Q: stock spt boost gauge   swinn935 years ago

    is this designed to work along with the stock spt boost gauge location?
    • 0 of 0 people found the following answer helpful

      A:  We have not tested fitment with the SPT boost gauge but depending on the exact orientation of the SPT pod this should fit without a problem.

      Nick S. @ RallySport Direct 5 years ago  
        
      Was this answer helpful?
  • Q: Fitment  strutton175 years ago

    Will 60mm prosport preformance gauges fit into this with the 10mm spacer?
    • 0 of 0 people found the following answer helpful

      A:  We cannot guarantee fitment with products we do not carry, but we have a few customers using Prosport gauges with this pod.

      Zach G. @ RallySport Direct 5 years ago  
        
      Was this answer helpful?
  • Q: Kelvin  Kelvin Ong6 years ago

    Hi, any right hand side product for this ATICenter Pod?
  • Q: fit  Gary137 years ago

    so when I installed the pod it looked perfect, I didnt use the screws(yet). But after a few days in the hot sun it seems to have shrunk Im just wondering if anyone else has had any issues with this.
    • 0 of 0 people found the following answer helpful

      A:  We have only had 1 issue with the pod shrinking and that customer was in a very hot climate and did not install the screws either. ATI took care of that issue very promptly and took the pod back for inspection. If you are having issues, then please contact an RSD representative for assistance.

      Zach G. @ RallySport Direct 7 years ago  
        
      Was this answer helpful?
  • Q: Fitment  NoOzL7 years ago

    Is this only for LHD cars, or is there a RHD version aswel?
    • 0 of 0 people found the following answer helpful

      A:  Unfortunately there is only a LHD version at this time as it points the gauges at a slight angle to the left seat. We haven't been made aware of any plans to make a RHD version at this time.

      Tanner S. @ RallySport Direct 7 years ago  
        
      Was this answer helpful?
  • Q: still work?  JLove187 years ago

    Im looking to buy this gauge pod because I like it a lot but I want the 3 gauges to be from perrin because I like the 2x sweep on start up but when your headlights are off the gauge lights are white but when headlights on they are red. Can that still work in this gauge pod?
  • Q:   Sharaf7 years ago

    @ RallySportDirect is there any way to di without drilling or other pods thats fit right awya insteat of the clock?
    • 0 of 0 people found the following answer helpful

      A:  It is possible to install this pod without drilling or screwing into the dash, but that may cause small fit and finish issues. Because this is designed to attach with screws it may rattle or show a gap around the edges if the pod is not attached with the supplied screws.

      Zach G. @ RallySport Direct 7 years ago  
        
      Was this answer helpful?
    • 1 of 1 people found the following answer helpful

      A:  You could use black silicone adhesive it will stick and seal the bottom to the dash without drilling and will withstand heat. I mounted my defi gauge pod with it and its still holding up

      subie doo
        
      Was this answer helpful?
  • Q: attachement  Go7 years ago

    where do you screw the pod? will you drill a hole? thanks
    • 0 of 0 people found the following answer helpful

      A:  The pod comes with pre aligned holes where you can drop the screw in which are self tapping.

      Kirill C. @ RallySport Direct 7 years ago  
        
      Was this answer helpful?
    • 0 of 0 people found the following answer helpful

      A:  There are two integrated slots in the pod where you would screw into the dash. The screws will not be visible once they've been installed.

      ATI Gauge Solutions @ ATI 7 years ago  
        
      Was this answer helpful?
  • Q: The custom wrap  GIJosh26877 years ago

    I am staring at this image of the pod with the custom wrap. I will be honest, where can I get a wrap job like that?
  • Q: running wires  dmastrop7 years ago

    How or where do u run the gauge wires through the dash...? I don't see any wires anywhere?
    • 0 of 0 people found the following answer helpful

      A:  Because this pod will cover the clock, the best place to route the wires would be where the stock clock would go. This will provide a very clean and simple install for the gauges. Thanks.

      Rick C. @ RallySport Direct 7 years ago  
        
      Was this answer helpful?
  • Q: rings  bandrade1021651017 years ago

    Does this package come with step down rings for all 3 because i might get 3 52mm gauges or is it better to get all 60mm gauges??
  • Q: View of back?  thaduke20037 years ago

    Is there any chance of getting a view of the back of this when mounted (through the windshield)? I'd like to see how clean the install is from that angle (no gaps, etc.). Thanks! Mark W.
  • Q: On top of screen  JLove187 years ago

    Im getting the new 2012 sti 5 door and above the navi there is a little hump that has a little screen that shows numbers can this gauge pod & gauges be placed on top of it?
    • 0 of 0 people found the following answer helpful

      A:  If you are referring to the hump in the dash that has the clock and the temperature read out then yes this gauge pod was designed to sit on top of that so you will lose that functionality when this unit is installed.

      Tanner S. @ RallySport Direct 7 years ago  
        
      Was this answer helpful?
  • Q: Fitting  maxx189750797 years ago

    Hello, do you think this gauge pod could fit a 2007 Legacy GT dash ? thanks.