SET YOUR CAR
TALK TO A PARTS EXPERT
- Exhausts
- Cat Back Exhaust System
- Downpipes And Y-pipes
- Exhaust Headers And Manifolds
- Exhaust Gaskets And Hardware
- Axle Back Exhausts
- Shop All
- Engine Management
- Plug And Play Engine Management
- Staged Power Packages
- Engine Management Sensors
- Stand Alone Engine Management
- Engine Management Harnesses
- Shop All
- Air Induction
- Short Ram Air Intakes
- Turbo Inlet Hoses And Pipes
- Cold Air Intakes
- Air Intake And Maf Hoses
- High Flow Replacement Panel Filters
- Shop All
Product images
Product Media
Community Media
Mishimoto Silicone Intercooler Hoses Black
Subaru WRX 2006-2007
Features & Product Details
RallySport Direct is proud to bring you a large selection of automotive performance products brought to you by Mishimoto.
On this page, you are looking at the Mishimoto Intercooler Hose Kit. This kit has been made using durable silicone fibers to be direct replacements for your factory intercooler hoses that can become weak over time.
Here are the details:
Specifications
Brand:
Mishimoto
Color:
Black
Includes New Clamps:
Yes
Material:
Reinforced Silicone
Number of Hoses:
3
PEOPLE WHO VIEWED THIS ITEM ALSO VIEWED
REVIEWS & CUSTOMER MEDIA
Customer Photos and Videos
1 of 1 people found the following review helpful
5out of
5stars
CarTerm
I was looking for a silicone y pipe for my 2005 Forester XT and was having trouble finding an exact part that was in stock. After a bit of research I landed on this set and took a risk of whether it would fit or not. It does fit without any trimming, but it's tight. A little isopropyl alcohol as lubricant worked well to slip the hose onto the aluminum pieces.
5out of
5stars
CarTerm
I was looking for a silicone y pipe for my 2005 Forester XT and was having trouble finding an exact part that was in stock. After a bit of research I landed on this set and took a risk of whether it would fit or not. It does fit without any trimming, but it's tight. A little isopropyl alcohol as lubricant worked well to slip the hose onto the aluminum pieces.
3out of
5stars
gijosiahh
(Installing on 2006 WRX) Quality seems good, but there are a few things that hold it back from being a good product. -The IC to TB hose was too long and would need to be trimmed for everything to fit properly. It was about .5" longer than stock and caused the Y-pipe to not fit correctly on the turbo end. -There was some excess rubber (casting flash) inside the Y pipe that needed to be removed. -The T-bolt clamps are good quality, however the bolt for the clamps for the IC to TB hose was too short and nearly impossible to get the nut started.
4out of
5stars
jason_the_angry
Package says no modification required... not sure about that for a 2007 WRX. Y-pipe showed instances of casting flash from the mold on the inside of the pipe that had to be trimmed with a razor before install. Not a major deal, but I expected a nice smooth contour from the factory. One leg of the Y had to be trimmed for length by about 0.5" to match stock geometry. 0.5" needed to be trimmed from the intercooler outlet hose as well. Snaking the BOV tube around and under the intake hoses was a bit of a nightmare; not Mishimoto's fault. The stainless clamps are great quality, but are quite a bit larger than stock, and won't fit in all places. Prepare to reuse a stock clamp or two. Overall? Still better than stock, especially for the Y-pipe. No change in performance for the install, but should not degrade like the cheap plastic and rubber units. I would not purchase these if your stock hardware works. If something is falling apart though, this is a good answer. Be standing by with just a little WD-40 to lube the interfaces between the silicone hose and the aluminum engine parts before installation. It makes it much easier.
4out of
5stars
NOVESKE
Instalation went well. It's pretty straight forward. The improved air flow is noticable. Throttle response is better and, boost delivery is smoother. The down side was that the clamps that go on the BPV hose did not fit. They were way to small. I had to use the oem clamps. A side note, You my need to reset your ecu after install. Disconnect your negative battery terminal and hold the brake peddal for 30 sec. With out doing this you might see inconsistent Idle and rpms fluctuate while in nutral. It takes about 200 miles after the reset for the car to learn your driving habits. An ecu reset will not erase your tune.
QUESTIONS & ANSWERS
-
Q: Will this kit require a tune? Dillon5 years ago
I'm looking to replace my OEM intercooler hoses (worn out, hard to reinstall) on my stock 07 WRX. Will these hoses require a tune or can I just plug and play?
-
-
0 of
0 people found the
following answer helpful
A: These are a direct OEM replacement and will not require any type of tuning.
Brady R @ RallySport Direct 5 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Mishimoto tmic hose kit tempemail55b414ffcaae5288048b6a966 years ago
-
-
0 of
0 people found the
following answer helpful
A: This is confirmed to fit with OEM spec products. So if your Turbo XS is using the stock hose then these will work.
Trevor C. @ RallySport Direct 6 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: 07 WRX Wagon Pdad6 years ago
-
-
0 of
0 people found the
following answer helpful
A: This will fit the wagon.
Stevens Henager @ RallySport Direct 6 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: 2006 wrx Jack_Bern6 years ago
-
-
1 of
1 people found the
following answer helpful
A: This will not fit the STi. You will want part number MIS MMHOSE-SUB-INT4BK.
Brady R. @ RallySport Direct 6 years agoWas this answer helpful?
-
1 of
1 people found the
following answer helpful
-
Q: 2006 subaru wrx mspruell496 years ago
-
-
0 of
0 people found the
following answer helpful
A: These will work with the OEM intercooler.
Kyle A. @ RallySport Direct 6 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
