- Exhausts
- Cat Back Exhaust System
- Downpipes And Y-pipes
- Exhaust Headers And Manifolds
- Exhaust Gaskets And Hardware
- Axle Back Exhausts
- Shop All
- Engine Management
- Plug And Play Engine Management
- Staged Power Packages
- Engine Management Sensors
- Stand Alone Engine Management
- Engine Management Harnesses
- Shop All
- Air Induction
- Short Ram Air Intakes
- Turbo Inlet Hoses And Pipes
- Cold Air Intakes
- Air Intake And Maf Hoses
- High Flow Replacement Panel Filters
- Shop All
-
Q: What size is the bolt for the U-Bracket? brettklynn477746 years ago
I'm thinking about adapting this to be able to remove the license plate and install a Tow Strap for track days. What size size is the bolt that attaches the U-bracket to the main shaft?
-
-
0 of
0 people found the
following answer helpful
A: That bolt is an M8x1.25 , 25mm in length.
Brady R @ RallySport Direct 6 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Hole Saw Size? brettklynn477747 years ago
-
-
0 of
0 people found the
following answer helpful
A: The widest part of the shaft is .812in diameter.
Brady R @ RallySport Direct 7 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Front mount required beam removal!!! tx07wrx100429 years ago
-
-
0 of
0 people found the
following answer helpful
A: Hello, I'm sorry we don't have a solution for you. Its only intended install is to thread in to the bumper beams tow hook hole. Mike
GrimmSpeedWas this answer helpful? -
0 of
0 people found the
following answer helpful
A: This relocation kit uses the stock tow hook mount in the factory bumper beam and if you don't have the stock bumper beam, then you would need to fabricate a bracket to hold the mount. I would inspect the factory mount and try to duplicate it the best you can.
Zach G. @ RallySport Direct 9 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: 2004 STi Fitment with Intercooler fritzy9 years ago
-
-
0 of
0 people found the
following answer helpful
A: As long as you have the oem tow hook hole still present in the bumper beam it will work! Mike
GrimmSpeedWas this answer helpful? -
0 of
0 people found the
following answer helpful
A: This uses the stock tow hook location in the bumper beam and as long as you retain the tow hook mount, this can be used with a FMIC.
Zach G. @ RallySport Direct 9 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: 2004 STI fitment robert7884722349 years ago
-
-
0 of
0 people found the
following answer helpful
A: Your tow hook hole is behind your fog cover. You can either remove it completely or cut in to it to install this kit. Mike
GrimmSpeedWas this answer helpful? -
0 of
0 people found the
following answer helpful
A: You can install it by either removing the fog light cover and running it without the cover or for a cleaner looking install you can drill a hole in your fog light cover right where the tow hook installs. We have done this on a few of our shop cars and it comes out looking very clean. Remember to measure twice and cut/drill once :)
guest5666f5312a8d25ff038bdab9 @Was this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: fitment Ethanwrxwagon11 years ago
-
-
0 of
0 people found the
following answer helpful
A: Some Vehicles may require the removal of the lower fog light cover for proper installation when the tow hook mounting hole is behind it. Modification to your fog light cover can be made to run this kit successfully however are not required.
Sterling W. @ RallySport Direct 11 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
