- Exhausts
- Cat Back Exhaust System
- Downpipes And Y-pipes
- Exhaust Headers And Manifolds
- Exhaust Gaskets And Hardware
- Axle Back Exhausts
- Shop All
- Engine Management
- Plug And Play Engine Management
- Staged Power Packages
- Engine Management Sensors
- Stand Alone Engine Management
- Engine Management Harnesses
- Shop All
- Air Induction
- Short Ram Air Intakes
- Turbo Inlet Hoses And Pipes
- Cold Air Intakes
- Air Intake And Maf Hoses
- High Flow Replacement Panel Filters
- Shop All
Kartboy Shifter Bushing Combo
Subaru 5MT Models (inc. 2002-2014 WRX)
Features & Product Details
This is the Kartboy shifter bushing combination for the 5 speed found on most Subaru models. However be sure to check on your confirmed applications list to make sure this will work on your vehicle.
This kit will eliminate any excessive play in your shifter mechanism due to tired, or worn out shifter bushings. With simple hand tools this kit can be installed on average in about 30 minutes. These bushings are 100% hand made in the U.S.A., and are made from high grade polyurethane to help restore and tighten your shifter feel.
Specifications
PEOPLE WHO VIEWED THIS ITEM ALSO VIEWED
REVIEWS & CUSTOMER MEDIA
One of my first mods. Still feels amazing.
These bushings made a huge difference in the shifter. Took all the slop out that the factory bishings had. Shifts are much tighter
My old bushings were blown. The shifter had so much slop. It felt like neutral in every gear. The kartboy bushings tightened everything up substantially. Huge improvement and a fairly straightforward install
I will be honest I can't tell how much of this is attributed to the bushing combo because I also replaced the shift linkage U-joint. That being said, it now feels like my Forester has a brand new gear shifter. I had a lot of free play before and now everything is crisp and clean. I had it installed though so I cannot speak to ease of install. I rated it neutral accordingly.
Can't tell you how much these improve the shifter feel. Much tighter and precise compared to the OEM bushings and its easy to tell why. Install isn't terrible but isn't the easiest thing I've ever done.
QUESTIONS & ANSWERS
-
Q: Rear hardware size Loganoak3 years ago
I purchased this and waited a while to put it on. In the process I ended up losing the hardware. Can you provide the thread size and length and details so I can purchase them?
-
-
0 of
0 people found the
following answer helpful
A: Kartboy doesn't sell the hardware separately unfortunately, but you should be able to find some replacement bolts, I'm not 100% sure of the thread pitch, but M12x1.25 or M12x1.5 is usually a good start.
Lane H. @ RallySport Direct 2 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Fitment? ACS14004 years ago
-
-
0 of
0 people found the
following answer helpful
A: Yes, this will fit.
Michael N.Was this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Will this fit benobrien5996 years ago
-
-
0 of
0 people found the
following answer helpful
A: We are only able to confirm these bushings to fit USDM models.
Chris W. @ RallySport Direct 6 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Kartboy vs Perrin/Cobb NuVision7 years ago
-
-
0 of
0 people found the
following answer helpful
A: All three brands will have a similar durometer. Exact measurements are not given.
Josh P. @ RallySport Direct 7 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Fitment Question mitchellkid8 years ago
-
-
0 of
0 people found the
following answer helpful
A: We recommend lubricating the rear bushing so the linkage will be able to slide a little bit, and that should allow you to line both up at the same time. Also make sure the rear bushing is being installed so that the front of the bushing is nearly vertical (correct side up).
Zach G. @ RallySport Direct 8 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
