
GrimmSpeed Phenolic Thermal Spacer 8mm
Subaru Models (inc. 2004+ STI / 2002-2014 WRX)
Features & Product Details
Phenolic spacers have been used for years by many other specialized automotive companies, but this is very new technology to the Subaru world.
What it does:
* Greatly reduces the transfer of heat from engine to intake manifold thus reducing heat soak.
* One of a kind true Phenolic material, not cutting board material like others.
* The cooler your intake temperature is the denser the air is which leads to more power
* For every 5 degree reduction in temperature, increases power by 1%.
* The cooler and denser the intake air that the engine sucks in, increases the amount of air that can be mixed with fuel thus increasing efficiency.
* Direct bolt-on.
* When running the oem gasket only, your intake manifold gets very hot to the touch, enough to burn your hand. When the oem gasket is replaced with GrimmSpeed's Phenolic Spacer, your hand can be placed on the intake manifold without any issues.
* GrimmSpeed has installed both with and without OEM Subaru Gaskets and have had no issues with either way. They do recommend using 2 sets of oem gaskets however, one on both sides of the spacer.
* USA made
Package Contents:
1 Pair Phenolic Thermal Spacers
8 Longer bolts with washers
Specifications
PEOPLE WHO VIEWED THIS ITEM ALSO VIEWED
REVIEWS & CUSTOMER MEDIA

These spacers fit perfect on my 06 wrx. Great quality, installation is a PITA but not impossible. Haven't been able to test the temp difference yet as I am currently in the process of rotating my turbo. Great product though.
Good item , don't miss to order all the gasket you need for install this item
I had issues with my sleeved block radiating heat up through the TGVs, then my cosworth intake manifold, and finally my ic-throttle body pipe where my speed density sesnor was located. This caused incredibly high IAT temps on the dyno. Since installing this my temps are far lower and the intake manifold is never hot to the touch unlike before. I'd highly recommend this product!
I recently went with a rotated turbo and intake manifold. I needed a little more height to clear the pipe past the p/s pump and for the top feed rails to clear the avcs. Not only do they look great but the 8mm still cleared my hood. Amazing product highly recommend.
Fitment is good. maybe heat soak is reduced a little bit. And intake manifold is also less hot when you put this spacer.
QUESTIONS & ANSWERS
-
Q: VertiTMIC FrankensteinWRX4 months ago
Would the Verti bracket for the TMIC help with fitment, using the 8 mm?
-
-
0 of
0 people found the
following answer helpful
A: No, the bracket will move the IC a bit lower. These are more meant for front mount set ups.
Lane H. @ RallySport Direct 2 months ago
-
0 of
0 people found the
following answer helpful
-
Q: FP Black Tomeii turbo inlet and TMIC, clearance or fitment issues unhappy turbo inlet1 year ago
Would this spacer help me with clearance issues with my FP inlet and allow for my TMIC setup?
-
-
1 of
1 people found the
following answer helpful
A: This spacer could help you with the clearance issues, but I would strongly recommend a FMIC setup. The reason being is that heat soak is going to be a huge factor here, with the FP Black being one of the largest OEM location turbos it is going to cause the TMIC to have fitment issues like you are currently running into, as well as major heat soak issues with the TMIC.
Tylo R @ RallySport Direct
-
1 of
1 people found the
following answer helpful
-
Q: 2008 sti luiseg11339602 years ago
Do the 8mm spacers work with the grimmspeed tmic ?
-
-
0 of
0 people found the
following answer helpful
A: You may run into fitment issues. The 8mm is meant more for FMIC, with the 3mm you should be able to get the TMIC to fit properly.
Michael N.
-
0 of
0 people found the
following answer helpful
-
Q: thermal spacer difference Patron2JZ2 years ago
What is the difference between the 8mm and the 3mm spacers? which one is for what type of setup?
-
-
1 of
2 people found the
following answer helpful
A: One is 3 MM thick and one is 8MM thick, depending on what TMIC you are running you may have issues when running the 8MM spacer, we only recommend the 8MM for FMIC set ups.
Jared A. @ RallySport Direct 2 years ago
-
1 of
2 people found the
following answer helpful
-
Q: FP green Tomeii turbo inlet amd ETS TMIC, clearance or fitment issues? aubreylanglinais2012864954 years ago
I'm running a stock location FP green with a Tomeii turbo inlet and an ETS TMIC. Will the 8mm cause any alignment or clearance issues on a 2014 sti?
-
-
0 of
0 people found the
following answer helpful
A: We are not able to confirm fitment on the FP turbos as we do not sell them.
Jared A. @ RallySport Direct 4 years ago
-
0 of
0 people found the
following answer helpful