SET YOUR CAR
Buy Now, Pay Later! Starting at 0% APR
FREE SHIPPING
On orders over $100
TALK TO A PARTS EXPERT
RALLYSPORT GUARANTEE
100% Money Back on Select Parts

PST Carbon Fiber Driveshaft

MODEL # PST IZW11160

$1,107.14


  • Q: HP  moonpie2 months ago

    Hp rating on this?
    • 0 of 0 people found the following answer helpful

      A:  Sadly, we would not have an exact hp rating on this part. You can call pst and they will explain the technical aspects of what it can do!

      Devan M. @ RallySport Direct 2 months ago  
        
      Was this answer helpful?
  • Q: Longevity?  Alec C.1 year ago

    Hi. How is it's longevity? I know it has a high torsion rating, and carbon fiber tends to be as strong, or stronger, than aluminum. But how is it for extended life for a daily driver? This is a must have if it lasts!
    • 0 of 0 people found the following answer helpful

      A:  Based off the quality alone it is guaranteed to last you a couple of years. It is hard to say exactly because we haven't had any issues with these and we haven't had any issues with driveshafts going out period.

      Tyler A. @ RallySport Direct 1 year ago  
        
      Was this answer helpful?
  • Q: 2008 2.5i MT  TGMChuck3 years ago

    This part says it will fit the 2008 WRX sedan. Will it also fit the 2008 2.5i MT sedan?
  • Q: weight  Cpeters6994 years ago

    what is the weight difference between the stock drive shaft vs. the cf shaft?
    • 0 of 0 people found the following answer helpful

      A:  We do not have the exact weight of the stock driveshaft, but it should be approximately 25-28lbs and this shaft is 15lbs.

      Zach G. @ RallySport Direct 4 years ago  
        
      Was this answer helpful?
  • Q: Fuel economy   tr3y.1990256974 years ago

    How much does this product help fuel economy? My car is a daily driver with allot of highway km so I'm looking to save a bit on gas which isn't cheap here in canada
    • 0 of 0 people found the following answer helpful

      A:  While lighter weight components do tend to be better for economy there is no data implying that a noticeable gain in fuel economy will be seen with this setup.

      Nick S. @ RallySport Direct 4 years ago  
        
      Was this answer helpful?
  • Q: Torsional Vibrations  4 years ago

    I've been told by a manufacturer of a WRX lightweight crankshaft pulley that installing BOTH the lightweight crankshaft pulley as well as a lightweight flywheel may lead to damaging torsional vibrations. Has this been observed or tested with the carbon fiber driveshaft installed with other inertia-reducing mods, such as: lightweight crankshaft pulley, lightweight flywheel, or reduced weight wheels?
    • 0 of 0 people found the following answer helpful

      A:  So far, we have not seen any issues with a lightweight flywheel and one of these driveshafts working together. Since the driveline is after the engine/transmission, the motor is basically unaware that anything has changed.

      guest57853c642a8d25b5018c44a7 @
        
      Was this answer helpful?
  • Q: driveshaft & pulley combo  losmanWRX5 years ago

    Will using this drive shaft with a light weight pulley cause any ECU issues?
    • 0 of 0 people found the following answer helpful

      A:  We have not found any problems with using a lightweight crank pulley and driveshaft together.

      Zach G. @ RallySport Direct 5 years ago  
        
      Was this answer helpful?
  • Q: weight?  sandman6 years ago

    any information on how much weight it drops from stock? 08wrx
    • 0 of 0 people found the following answer helpful

      A:  The stock driveshaft is in the neighborhood of about 25-30 lbs, but we do not have an exact weight. This Carbon Fiber driveshaft significantly drops weight and increases power put to the ground of your vehicle.

      Nick S. @ RallySport Direct 6 years ago  
        
      Was this answer helpful?
  • Q: U-Joints  Magnum4216 years ago

    What happens when the U-joints on this shaft wear out? Can they be replaced? If yes, does it have to be the same kind that came with the driveshaft or can we use regular OE type U-joints?
    • 0 of 0 people found the following answer helpful

      A:  This driveshaft actually uses the factory yoke as well as the U-joints, so they should be the same as the OEM U-Joints.

      Nick S. @ RallySport Direct 6 years ago  
        
      Was this answer helpful?
  • Q: 2012 WRX Sedan / Manual Transmission Fitment?  VaughanJer6 years ago

    Will this fit a 2012 WRX sedan? I see that it lists that it fits for the 2011 WRX, which I think is the same, but I'm not positive.
  • Q: Installation   xrs310x171826 years ago

    Do you have to make any modification to install this driveshaft ?
    • 0 of 0 people found the following answer helpful

      A:  No modification will be necessary as this driveshaft is a direct replacement for the OEM shaft. The carrier bearing will not be used with this 1 piece shaft though.

      Zach G. @ RallySport Direct 6 years ago  
        
      Was this answer helpful?
  • Q: Streetable  3g_wrx6 years ago

    How would these stand up to daily summer driving?
    • 0 of 0 people found the following answer helpful

      A:  There would be no problem at all. Carbon shafts have been used in cars all over the world and in all conditions without any issues. Thanks, Rick

      Rick C. @ RallySport Direct 6 years ago  
        
      Was this answer helpful?
  • Q: Carbon Fiber vs heavy metal  st3ph3nn3umann262606 years ago

    From what I've seen with hoods and other carbon fiber parts they crack very easy. What is this driveshaft rated to? Will it be reliable to use on a car that has been modified to much higher whp/tq than stock?
    • 3 of 3 people found the following answer helpful

      A:  The bonding agent along with orientation of the carbon is designed specifically for torsional rigidity. These shafts are rated at over 2700lb-ft of tq before they start reaching a critical bending angle at which the resin and carbon begin to be put into danger of failure. With that being said PST carbon tubes have been used on drag cars running 6 second passes, and we have yet to see any failures occur do to torsional stress.

      Kirill C. @ RallySport Direct 6 years ago  
        
      Was this answer helpful?