- Exhausts
- Cat Back Exhaust System
- Downpipes And Y-pipes
- Exhaust Headers And Manifolds
- Exhaust Gaskets And Hardware
- Axle Back Exhausts
- Shop All
- Engine Management
- Plug And Play Engine Management
- Staged Power Packages
- Engine Management Sensors
- Stand Alone Engine Management
- Engine Management Harnesses
- Shop All
- Air Induction
- Short Ram Air Intakes
- Turbo Inlet Hoses And Pipes
- Cold Air Intakes
- Air Intake And Maf Hoses
- High Flow Replacement Panel Filters
- Shop All
Cusco Rear Strut Tower Bar Type OS
Subaru WRX/STI 2008-2014
Features & Product Details
RallySport Direct proudly carries some of the best suspension and drivetrain modifications brought to you by the industry leaders at Cusco.
Here, you are looking at the Cusco Type OS Rear Strut Tower Brace. This brace has been designed to bridge together the two rear strut towers to reduce chassis flex for improved balance and handling under hard cornering.
DETAILS:
Specifications
PEOPLE WHO VIEWED THIS ITEM ALSO VIEWED
REVIEWS & CUSTOMER MEDIA
I'm 100% Cusco for suspension parts as there products are of the best quality for both performance and aesthetics. Bit of a PITA as mentioned with the sedan passenger side install. Simplify install and bolt on without bar attached. Significantly easier whether installing or removing. Cusco provides measurements and photos for cutting insert, but I couldn't resist a large cut to show off all the hardware (helped insert lay flat as well otherwise it pops up a bit). Thanks for the continued quality Cusco, and thank you RSD for continuing to supply JDM parts!
I love Cusco products and finally saw they were running a sale so i snagged another bracing piece for the WRX. If you dont already know, installing a rear strut bar on your WRX/STi is a pain. That is if youre keeping your carpet. If youre planning on taking out your trunk carpet itll be a piece of cake.
just let u guys know it fit on forester rear strut tower bar.every thing from wrx and sti base it will fit on the forester.
This is an item fro this website that does NOT match Cusco's website. This strut bar does fit a 2010-2012 Legacy NA/GT. The only issue you will of course run into is removing/cutting the boot trim.
Bought it even though its not confirmed to fit and it went in no problem! Stoked on it, feels great!
QUESTIONS & ANSWERS
-
Q: Fuel line in the way? jcerillo70215518 years ago
On my wagon the fuel line is very stiff and in the way, and i dont want to force it over. What did you guys do? I dont want to break it.
-
-
1 of
2 people found the
following answer helpful
A: It sounds like some have had success removing the protector and moving the line out of the way. If there is any doubt, you can always have a mechanic take a look at the installation.
Was this answer helpful? -
0 of
0 people found the
following answer helpful
A: On my 2011 STI Limited, the fuel line was also in the way on the right hand (passenger) side. Moving it was not an option unless I wanted to bend a new one. Perhaps against my better judgment, I simply notched the mounting bracket on the strut bar by about 3mm with a dremel. With the thickness of the material on the bracket, I don't think it will have significantly weakened it.
SynapseWas this answer helpful?
-
1 of
2 people found the
following answer helpful
-
Q: 2010 Impreza 2.5i Hatch Wilcox9 years ago
-
-
0 of
0 people found the
following answer helpful
A: I would assume this would fit however, we can not guarantee it.
guest57853c642a8d25b5018c44a7 @Was this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: trunk pad/liner modification richie189 years ago
-
-
0 of
0 people found the
following answer helpful
A: Most people use a utility knife to trim the liner.
Zach G. @ RallySport Direct 9 years agoWas this answer helpful? -
0 of
0 people found the
following answer helpful
A: Zach, my liner is pretty thick. I'm surprised the a utility knife would do the job...was expecting that ppl used a dremel or something
richie18Was this answer helpful? -
0 of
0 people found the
following answer helpful
A: We used a dremel and a cutting wheel when we installed on my friend's hatch. A utility knife did not do the job.
jm02466Was this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Figment question Mrjurenka164919 years ago
-
-
0 of
0 people found the
following answer helpful
A: This is confirmed to fit on the 2013 WRX Hatchback. Thank you.
Sterling W. @ RallySport Direct 9 years agoWas this answer helpful? -
0 of
0 people found the
following answer helpful
A: This is confirmed to fit on the 2013 WRX Hatchback. Thank you.
Sterling W. @ RallySport Direct 9 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Cusco Quick Release Lever opramwew9 years ago
-
-
0 of
0 people found the
following answer helpful
A: Yes, search part number CUS 00B 540 C in the search bar and it should bring them up.
Nick S. @ RallySport Direct 9 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
