SET YOUR CAR
Buy Now, Pay Later!
FREE SHIPPING
On orders over $200
TALK TO A PARTS EXPERT
RALLYSPORT GUARANTEE
100% Money Back on Select Parts

Invidia N1 Cat Back Exhaust Titanium Tips

MODEL # INV HS08STIGTT

$690.94


  • Q: Will it fit  Scoobs 3 months ago

    Will this exhuast fit a 2008 wrx hatchback or will it only fit the sti
  • Q: Gaskets rusted out, what replacements do I need?  Saeven9 months ago

    I've had this exhaust for a few years now, and the gaskets have died (rusted and blown out). I can't seem to find a spec on gasket size, or a link to where I could buy replacements. Any help appreciated.
    • 0 of 0 people found the following answer helpful

      A:  Any 2-bolt 76mm (3 inch) universal exhaust gaskets should work. GRM 076001 should work for you.

      Marcus E. @ RallySport Direct 8 months ago  
        
      Was this answer helpful?
  • Q: Loudness  WrxonWrxOff1 year ago

    How loud is this exhaust compared to other cat back exhausts? Measurements in DB?
    • 0 of 0 people found the following answer helpful

      A:  Unfortunately we do not have the exact measurements but this is one of the loudest catbacks we sell. Please refer to sound clips that we have posted on our various pages.

      Tyler A. @ RallySport Direct 1 year ago  
        
      Was this answer helpful?
  • Q: Fit a sedan  Lapissti1 year ago

    Would this exhaust fit a 2008 sti sedan or just the hatchback
    • 0 of 0 people found the following answer helpful

      A:  This will just work for the Hatchback and not the Sedan do to the over length differences between the vehicles.

      Evan M. @ RallySport Direct 1 year ago  
        
      Was this answer helpful?
  • Q: Gasket for my Perrin downpipe?  jlockett1 year ago

    Good afternoon, I am trying to figure out what size gasket I will need for this N1 and my Perrin downpipe on my 08 STI hatchback. I believe my Perrin is 3" and it appears the N1 is 3" as well I just want to make sure I get the correct gasket. Thanks
    • 0 of 0 people found the following answer helpful

      A:  This exhaust comes with a 3 inch, 2 bolt gasket for you to mate up your 3 inch Perrin downpipe. Everything should mate up just fine.

      Tyler A. @ RallySport Direct 1 year ago  
        
      Was this answer helpful?
  • Q: Compatibility rear attachement Q300 and N1  Q300 and N1 rear attachement1 year ago

    Hello, I have allready the Q300 on my 2011 sti hatchback. Can you please tell or confirm me if I can switch only the rear dual muffler between the two Without touch the middle pipe. Tanks a lot. Best regards. Do I need anythink more part to install it?
    • 0 of 0 people found the following answer helpful

      A:  It does appear that the N1 and Q300 do share the same midpipe section, however we cannot 100% confirm the cross compatibility and you would need to contact Invidia to see if they have more info.

      Brady R @ RallySport Direct 1 year ago  
        
      Was this answer helpful?
  • Q: Fitment  3DSoundBlast1 year ago

    Will this fit right onto an invidia catless downpipe or will i need other parts?
  • Q: Weight  chad2 years ago

    Whats the weight of this, including the box and all its contents.
  • Q: additional parts  YummyDill2 years ago

    Will i need any additional parts to go with this
    • 0 of 1 people found the following answer helpful

      A:  You will need https://www.rallysportdirect.com/part/exhaust-gaskets-and-hardware/grm-077044-grimmspeed-3in-downpipe-to-stock-cat-back-adapter and https://www.rallysportdirect.com/part/exhaust-gaskets-and-hardware/sub-44022aa123-subaru-oem-donut-gasket If you are pairing with the OEM down pipe.

      Jared A. @ RallySport Direct 2 years ago  
        
      Was this answer helpful?
  • Q: Invidia n1 for my hatch   Rudyalas87859762 years ago

    This will fit to my stock down pipe with no modification or will I need anything else Thanks
    • 1 of 1 people found the following answer helpful

      A:  You will need an adapter (GRM 077046) to get this to fit to the OEM down pipe.

      Chris W. @ RallySport Direct 2 years ago  
        
      Was this answer helpful?
    • 0 of 0 people found the following answer helpful

      A:  Do you have the part number so I can order togheter thank you

      Rudyalas8785976
        
      Was this answer helpful?
  • Q: 2010 Impreza 2.5i  NotWrx2 years ago

    Will this fit an Impreza 2.5i sedan? It is a 2010 Impreza 2.5i
  • Q:   peterdoss32 years ago

    Do I need new hangers for my new n1 dual cat back exhaust on 2012 wrx hatch ?
    • 0 of 0 people found the following answer helpful

      A:  You can purchase new hangers if you would like, but you are able to utilize your OEM ones.

      Chris W. @ RallySport Direct 2 years ago  
        
      Was this answer helpful?
  • Q: Downpipe   Tyler3 years ago

    I have a completely stock exhaust system, and would like to purchase this exhaust, however i do not know whether or not an aftermarket downpipe and/or adapters are needed.
    • 0 of 0 people found the following answer helpful

      A:  You can run this exhaust with your OEM downpipe with an adapter. GRM 077046 is the adapter I would recommend.

      Chris W. @ RallySport Direct 3 years ago  
        
      Was this answer helpful?
  • Q: Cobb Catted Downpip  Boostaru293 years ago

    Hey RSD! I have a Cobb catted downpipe installed already. Will i need any adapters or just the standard 3" gaskets? and if im using the standard 3" gaskets do i need a donut gasket? Thanks.
    • 0 of 0 people found the following answer helpful

      A:  We recommend using Grimmspeed's stock downpipe to 3" catback adapter for that kind of a setup.

      Nick S. @ RallySport Direct 3 years ago  
        
      Was this answer helpful?
  • Q: perrin downpipe  John 3 years ago

    will this exhaust work with my perrin catted downpipe
  • Q: Weight comparison  klopez2043 years ago

    How much does this exhaust weigh compared to the stock exhaust ?
  • Q: Invidia Down pipe  julian.h.fehr135303 years ago

    Will this exhaust fit with an Invidia catless down pipe?
    • 0 of 0 people found the following answer helpful

      A:  Yes, this will bolt right up to Invidia's downpipe.

      Brady R. @ RallySport Direct 3 years ago  
        
      Was this answer helpful?
    • 0 of 0 people found the following answer helpful

      A:  Yes, This will be a direct fit with the invidia downpipes confirmed for the same fitment.

      guest569faaee2a8d2517038b4568 @
        
      Was this answer helpful?
  • Q: N1 Dual vs. Q300?  Nic3 years ago

    I am looking for a nice CBE to match up with my Cobb DP and noticed a $300 difference between the N1 and Q300. Is there any noticeable HP gain difference of them?
    • 0 of 0 people found the following answer helpful

      A:  Differences between catbacks mostly comes down to the style and volume. The N1 is going to be much louder than the Q300.

      Nick S. @ RallySport Direct 3 years ago  
        
      Was this answer helpful?
  • Q: fitment?  joshejones076414 years ago

    so I have a 2010 wrx hatch. I modified my bumper to fit a quad tip exhaust. my question is. will this fit a 2010 wrx hatch? I realize it is for 11+ wrx. But I currently have a 2011+ Q300 quad tip on and it fits. I ask because the Hangers look a little off in the pictures supplied, compared to the Q300 quad tip. I also know this is meant for 2011+ only. But isnt the piping the same on the 08+ WRX? any help would be appreciated. Thanks!.
    • 0 of 0 people found the following answer helpful

      A:  We do not have the ability to confirm fitment on your 2010 WRX hatch and it is likely modification will be required.

      Nick S. @ RallySport Direct 4 years ago  
        
      Was this answer helpful?
  • Q: Tune  TopGun914 years ago

    Is a tune required to run this exhaust?
    • 0 of 0 people found the following answer helpful

      A:  Hello, a tune is not required to run this exhaust. Thank you

        
      Was this answer helpful?
  • Q: UK models  Mattybell_4 years ago

    Will this fit a 2009 STI Hatchback UK Model?
    • 1 of 1 people found the following answer helpful

      A:  This exhaust should fit UK models, but we unfortunately cannot guarantee fitment on cars outside the USA. If your stock catback is the same length as USDM models, then this would fit.

      Zach G. @ RallySport Direct 4 years ago  
        
      Was this answer helpful?
  • Q: how many hangars are used?  Grat13324 years ago

    How many hangars are used? i know the stock ones will work but I'm looking to add some fore with some red perrin hangars.
  • Q: fitment   tommyjtr124465 years ago

    i have the cobb dp and just want to know if this exhaust is a straight bolt up or do i need anything else ?
    • 0 of 0 people found the following answer helpful

      A:  This exhaust will be a direct fit with the Cobb downpipe and nothing else is needed.

      Zach G. @ RallySport Direct 5 years ago  
        
      Was this answer helpful?
  • Q: Cats?  gonzales_eleno350725 years ago

    So just wondering if this exhaust has cats and is Cali legal
  • Q: Mid pipe  Subeee5 years ago

    Had a quick question about that thing that is in front of the resonator, what is that called and what does it do? Thanks!
    • 0 of 0 people found the following answer helpful

      A:  The piece in front of the resonator is a flex joint and it is designed to reduce stress on the other exhaust components.

      Zach G. @ RallySport Direct 5 years ago  
        
      Was this answer helpful?
  • Q: install  subawho5 years ago

    Will this bolt up nicely to the stock downpipe, I've heard people having fitment issues with stock dp? Also will it come with the required donut gasket?
    • 0 of 0 people found the following answer helpful

      A:  This exhaust will fit well with the stock downpipe and OEM donut gasket. The donut gasket is not included with this and you can generally reuse the stock gasket if it is less than 1 year old.

      Zach G. @ RallySport Direct 5 years ago  
        
      Was this answer helpful?
  • Q: please respond?  bulletproof0905 years ago

    does This Product Just Bolt On To The Cat For Easy installation or Does It Need To Be Welded, And If You Leave The Silencer Off Do You Need A replacement Or will It Still Bolt On Perfect?
    • 0 of 0 people found the following answer helpful

      A:  This will be a direct bolt on, no cutting or welding needed. You can remove or install the silencers when you want. As they just bolt on to the muffler.

      Kyle A. @ RallySport Direct 5 years ago  
        
      Was this answer helpful?
  • Q: 2008-2010 Fitment?  BroncoTurbo5 years ago

    Will this setup work with a 2008 WRX Hatchback? I can get a dual exit diffuser for the back, but are the hangers different for the '11+ than the '08-'10?
  • Q: silencers  anthonyc1024516905 years ago

    how quiet will the silencers make this exhaust?
    • 1 of 1 people found the following answer helpful

      A:  It will be a very noticeable difference in noise with the silencer in. However as a result you will also see a reduction in power as you will be ultimately reducing the size of the hole that flow is able to pass through.

      Kirill C. @ RallySport Direct 5 years ago  
        
      Was this answer helpful?
  • Q: How much does this exhaust weigh?  stickyfingaz295 years ago

    How much does the whole setup weight? and compared to the N1 single exit?
    • 0 of 0 people found the following answer helpful

      A:  I only have the shipping weights of these products. The dual exit is 48 lbs and the single is 41 lbs.

      Nick S. @ RallySport Direct 5 years ago  
        
      Was this answer helpful?