SET YOUR CAR
As low as 0% APR - Buy Now, Pay Later!
FREE SHIPPING
On orders over $200
TALK TO A PARTS EXPERT
RALLYSPORT GUARANTEE
100% Money Back on Select Parts

Eibach Camber Bolts

MODEL # EIB1 5.81260K

$25.11


  • Q: Rear coilover installation  Rob4 months ago

    Can these be used on the rear coilovers? Description says for front only.
  • Q: 2004 sti stock suspension   Blue04sti5 months ago

    Will these work for front and rear? I see it says for front but then I see an answer says meant for rear?? Will these work for front and rear for 04 sti with stock suspension? What camber bolts will work for front and rear? Thanks
    • 0 of 0 people found the following answer helpful

      A:  These will only work for the front as there is not a location for the rear camber bolts on Subaru's.

      Brady R @ RallySport Direct 3 months ago  
        
      Was this answer helpful?
  • Q: 06 sti   pattara6 months ago

    will they work for the front and rear. what hole do i put them in and what are the torque specs on them?
  • Q: Subaru WRX 03 feal 441 Coilovers Rear  Paul 2 years ago

    Will these work on Feal 441 Rear coilovers to adjustment camber ?
  • Q: 2005 WRX rear strut holes  alexvc2 years ago

    Will these work in the rear lower strut hole? My Fortune Auto coilovers have slotted upper strut holes (so I assume they won't work there)
    • 0 of 0 people found the following answer helpful

      A:  Depending on if you coilovers are compatible with these, I attached a guide below. http://www.forcedfabllc.com/assets/images/products/81250__29776.jpg

      Trevor C. @ RallySport Direct 2 years ago  
        
      Was this answer helpful?
  • Q: fitment  Pspmskt205823 years ago

    will these work with my Tein Street Basis coilover is have instatlled on my 2009 WRX?
    • 0 of 0 people found the following answer helpful

      A:  These will fit any vehicle using an OEM replacement suspension like your Tein Street Basis.

      Nick S. @ RallySport Direct 3 years ago  
        
      Was this answer helpful?
  • Q: Top or Bottom?  thescreensavers3 years ago

    Seem to be reading a lot of wrong info on this. This bolt is to be used with the OEM camber bolt so it should go in the bottom correct? Not the Top?
    • 0 of 0 people found the following answer helpful

      A:  Yes, you will want to install thin in the bottom and keep the OEM Bolt on the top.

        
      Was this answer helpful?
  • Q: 2006 WRX with Eibach Pro Kit  chrisjion84709783 years ago

    I plan on installing the Pro Kit lowering springs, just to be clear, will I need to order 2 sets of these camber bolts (one for the front and one for the rear) so that I may have a proper alignment done after the install?
  • Q: fitment  john guy3 years ago

    Just making sure, will these work with a 06 wrx limited rear?
  • Q: 2011 wrx fitment   Scoobysteve114 years ago

    Why is there so many people saying this didn't fit their car.? Reviews say too small.? Also which will give me more camber these or whiteline.? And last is it safe and/useful for max camber to get both bottom and top camber bolts for max camber.?
    • 1 of 1 people found the following answer helpful

      A:  There will only be fitment issues on the front of a Subaru if these bolts are being used to replace the stock camber bolts. These bolts should be used in addition to the stock camber bolts in the lower hole on the front knuckles. Camber bolts need to be installed in a round hole and the upper hole on Subarus is oblong because the factory camber bolts are a different design. The Eibach camber bolts claim to have 1.75 degrees of adjustment and Whiteline camber bolts have 1.5 degrees of adjustment. We do not recommend using these bolts in the upper hole on the front of Subaru models because they will be loose.

      Zach G. @ RallySport Direct 4 years ago  
        
      Was this answer helpful?
  • Q: Camber bolts for the rear? 03 WRX Sedan  blakexr100021934 years ago

    I am going to be doing KYB adjustable Struts, Eibach pro kit lowering springs, and Group N top hats for the front. Will I need camber bolts for the front and rear?
    • 0 of 0 people found the following answer helpful

      A:  It would be recommended to get these as it will help you get proper alignment after installation.

      Kyle A. @ RallySport Direct 4 years ago  
        
      Was this answer helpful?
  • Q: Fitment  Mason02wrx4 years ago

    2002 wrx with BC BR coils, would these fit the rear?
  • Q: Would it fit?  Mason02wrx4 years ago

    Would these fit a 2002 wrx with BC BR coil overs?
  • Q: Rear camber   d.fonseca7475934 years ago

    Will I be able to get some negative camber on the rear of my 2014 wrx?
    • 0 of 0 people found the following answer helpful

      A:  This will not work for the rear of your vehicle, you will want to use aftermarket control arms to adjust camber.

      Kyle A. @ RallySport Direct 4 years ago  
        
      Was this answer helpful?
  • Q: Eibach Pro Kit Springs  Josh A.4 years ago

    I plan on ordering the Eibach Pro Kit springs for my 2013 wrx sedan. Now I see that these only work for the front. What will I need to use for the rear? And are these all I need to make sure my alignment is correct?
    • 0 of 0 people found the following answer helpful

      A:  For the rear there is not a place to use camber bolts. To adjust rear camber you will need adjustable lower control arms or special offset upper control arm bushings.

      Kirill C. @ RallySport Direct 4 years ago  
        
      Was this answer helpful?
  • Q: Rear Camber  adamshalom203344 years ago

    I have an 05 sti, will I have to purchase lateral links as well for proper adjustment of rear camber or will the bolts alone be sufficient? Thanks.
    • 0 of 0 people found the following answer helpful

      A:  These will work on both front and rear of the 2005 STI, although they are limited and do not have as much adjustment as lateral links.

      Nick S. @ RallySport Direct 4 years ago  
        
      Was this answer helpful?
  • Q: 2013 Wrx Install  mugentheman2154 years ago

    I purchased Eibach Pro Kit lowering springs and was suggested by the installer to get camber bolts to bring the alignment back into spec. When installing these are they swapped with the ones on the top or bottom hole?
  • Q: 1995 Legacy Fitment  stokes.william172674 years ago

    Will these bolts fit the rear of a 1995 Legacy? I'm assuming they will fit the front.
  • Q: 2002 wrx rear  axelbowen667484 years ago

    Hi! will these camber bolts fit to the rear of my 2002 wrx. Currently running KYB Gr2s with Swift Sport springs. Thanks!
  • Q: Apexi N1 Coilovers  Wicked_STI4 years ago

    I just received my coilover kit and the fronts are adjustable but the rear isn't, would I need to get these camber bolts for my rears to align the toes properly? Thank you RSD!
    • 2 of 2 people found the following answer helpful

      A:  These are designed to only work on the front of most applications. We recommend purchasing adjustable lateral links for proper camber adjustment. Thank you.

      Sterling W. @ RallySport Direct 4 years ago  
        
      Was this answer helpful?
  • Q: 2014 STi Sedan  AWDsnail145 years ago

    Will these bolts also allow me to adjust camber in the rear of my 2014 STi sedan?
    • 0 of 0 people found the following answer helpful

      A:  They will not, For the rear in the 08+ sti you will want to use lateral links to adjust camber.

      Kyle A. @ RallySport Direct 5 years ago  
        
      Was this answer helpful?
  • Q: Tein super streets fitment..  jbryar5 years ago

    Hello - will these fit my rear tein super streets? I drive a 2006 Impreza wagon. Cheers, J.
    • 0 of 0 people found the following answer helpful

      A:  They will fit but due to the no factory adjustment for camber on your car this will allow for some camber adjustment. However the adjustment range will be less then what you are able to get on the front.

      Kirill C. @ RallySport Direct 5 years ago  
        
      Was this answer helpful?
  • Q: 2012 Subaru WRX Hatch  rosedaleny8065 years ago

    Will these fit front and back on my 12' hatch???
  • Q: Forester   Chrisbauman123191165 years ago

    Will these replace the rear camber bolts on a 99 forester
    • 0 of 0 people found the following answer helpful

      A:  These camber bolts can be used on the rear of a 1999 Forester.

      Zach G. @ RallySport Direct 5 years ago  
        
      Was this answer helpful?
    • 0 of 0 people found the following answer helpful

      A:  Hi Chris, unfortunately We(Eibach)have not verified fitment for the Forester Rears. I can tell you though that it is the same part number for the front or rear of the 93-01 2.5L Impreza.

      Mark @ Eibach @ Eibach 5 years ago  
        
      Was this answer helpful?
  • Q: Bolts thickness for Subaru Legacy 2010  gborja8885 years ago

    Since my car is a JDM model. I just want to make sure before I purchase, I want to know the thickness and length of this camber bolts for Subaru Legacy 2010 model?
  • Q: 2010 Subaru Legacy fitment  gborja8885 years ago

    Just curious if my existing car already have an OE camber bolts (upper) in the front, does this replace the existing one? Or this replace the lower/bottom one which is regular bolt?
  • Q: no coilovers  DjTrix5 years ago

    Can I install these camber bolts if I do not have coilovers? Stock suspension.
  • Q: '06 STi fitment?  gregroot1985215 years ago

    So, to make sure I'm reading correctly, these will fit on both the front and rear of my '06 STi? Just need 2 sets to do it obviously.
    • 0 of 0 people found the following answer helpful

      A:  Correct, you would be able to install these on both the front and the rear of your vehicle.

      Nick S. @ RallySport Direct 5 years ago  
        
      Was this answer helpful?