SET YOUR CAR
TALK TO A PARTS EXPERT
- Exhausts
- Cat Back Exhaust System
- Downpipes And Y-pipes
- Exhaust Headers And Manifolds
- Exhaust Gaskets And Hardware
- Axle Back Exhausts
- Shop All
- Engine Management
- Plug And Play Engine Management
- Staged Power Packages
- Engine Management Sensors
- Stand Alone Engine Management
- Engine Management Harnesses
- Shop All
- Air Induction
- Short Ram Air Intakes
- Turbo Inlet Hoses And Pipes
- Cold Air Intakes
- Air Intake And Maf Hoses
- High Flow Replacement Panel Filters
- Shop All
Product images
Product Media
Blouch Oil Feed Line
Subaru WRX 2002-2007 / STI 2007
Product Resources
Features & Product Details
RallySport Direct proudly carries a large selection of turbochargers and turbocharger accessories brought to you by Blouch Performance Turbo.
This is the Blouch Performance Turbo Oil Feed Line. This oil feed will work with many Blouch journal bearing turbochargers, and this particular line will come in a specific length to work with your application.
DETAILS:
NOTE:
Specifications
Brand:
Blouch
Material:
Stainless Steel
QTY:
1
Mfgr. Warranty:
No Warranty
Condition:
New Product
Return Policy:
Standard
PEOPLE WHO VIEWED THIS ITEM ALSO VIEWED
REVIEWS & CUSTOMER MEDIA
Customer Photos and Videos
No user media. You can upload a photo or video of your install by posting a review.
5out of
5stars
InnKeepr
Installed with new Blouch 16GXT . Minor complaints. 1- no crush washers included. Had o check 3 different parts store as none had them in stock ( my luck ). and 2. The line in my opinion is about an inch and a half too long. This may be done to prevent a kink in the line - which is fine with me, just a little care needed while attaching it to the turbo. It is a good quality item, and a must have for your Blouch turbo. No leaks during initial prime, 3 minute idle test was good, and after 10 minute idle - nothing ! very happy so far.
4out of
5stars
igot4wrx
I thought this line will be a plug and play to my MY06 wrx w/vf43. the fitting at the big banjo bolt side(oil feed) is not align with the cylinder head(i need to bolt the line horizontally to clear the uppipe bracket.). Because the banjo adjustment nut is too big and cannot clear with the edge of the head. So end up i need to shave the cylinder head enough to get clearance. Wasn't a big deal for me but if u a DIYer then u need to prepare to shave a little bit of ur cylinder. good luck out there
5out of
5stars
liL MiX3D
Stock application was leaking from an COPPER-O ring. not the welds as usual but replaced it on my. 2006 Subaru Impreza WRX sedan.. it was a perfect fit and be sure to replace all of the OEM copper RINGS AND OIL FEED LINE BOLT W/ or WITHOUT the CORE FILTER> either one will work. love the swap it looks great and i know will last quality part IMHO. and is already able to allow me to upgrade my turbo when i am ready to mod my stock subie.
5out of
5stars
Xavstier
Awesome product and so much easier to work with than the OEM feed line. Also it fits my vf43 turbo on my 2007 sti!
3out of
5stars
trevorglinsbockel45781
FAST SHIPPING, good quality part. A bit expensive, but I had no choice as I have a 20gxt on the car now. The fitting that goes into the block isn't fixed, and can swivel with a union. The problem is, that when the fitting is bolted to the car, you can't adjust the union because its too close to the block. So you have to tighten the union first by SAFELY squishing this thing in a vice and tightening it with a wrench. And when you go to bolt it on, the union might be tightened to an orientation point where the hex point hits the block, so you'll have to loosen it and try again. I thought this design was pretty foolish. Also, if its not tight enough and won't seal, you'll never know it because you have to put the turbo back on and hook EVERYTHING up before you can start the car. And if it leaks, you're finished, and have to remove everything again to re tighten the union fitting. Now your up pipe and downpipe gaskets have been crushed and may have to be replaced... lucky for me I had no leaks, but I was terrified I would have one! Other than this design flaw, its a nice feed line.
QUESTIONS & ANSWERS
-
Q: Fitment Gomesypoo3 years ago
Will this fit a 2.5 polka pickle?
-
-
0 of
0 people found the
following answer helpful
A: The polka pickle is a ball bearing turbo not a journal bearing, so this will not work.
Devan M. @ RallySport Direct 3 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Will this fit a 2004 Subaru Forester XT tdo4 04fxtsubie5 years ago
-
-
0 of
0 people found the
following answer helpful
A: This oil feed line is NOT an OEM replacement and is only meant to be used with Blouch journal bearing turbos. We only have oil feed lines for aftermarket turbos.
Chris W. @ RallySport Direct 5 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Blotch Oil feed line connoremullins56de48464da8c322298b45855 years ago
-
-
0 of
0 people found the
following answer helpful
A: This oil feed line is not intended for use with stock turbos. It should only be used on Blouch turbos.
Josh P. @ RallySport Direct 5 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: 06 wrx hardware Dasmescar5 years ago
-
-
0 of
0 people found the
following answer helpful
A: We carry the OEM banjo bolt as Part #: SUB 14445AA090
Nick S. @ RallySport Direct 5 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: 2004 forester XT Mason5 years ago
-
-
0 of
0 people found the
following answer helpful
A: This is the correct oil line for journal bearing turbos and should work for your 04 FXT running a 16g.
Brady R @ RallySport Direct 5 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
