AEM Electronics Water / Methanol Injection Kit V2 (up to 35psi) w/ 1 Gallon Tank
Universal
Features & Product Details
RallySport Direct proudly carries a great selection of quality upgrades brought to you by AEM Performance Electronics.
Here, you are looking at the AEM V2 Water/Methanol Injection Kit. This is ideal for those of you who need to increase the octane out of your pump gas who want to increase the boost and ignition timing without having to resort to race gas. This is a great performance upgrade for your racecar, rally car, overlander or even your high horse powered daily driver!
DETAILS:
Specifications
PEOPLE WHO VIEWED THIS ITEM ALSO VIEWED
REVIEWS & CUSTOMER MEDIA
Fast delivery. Install the kit on my 2009 Subaru GH8 Auto and it works well. Very quiet pump. Easy to adjust the settings on the controller. No issue under hard driving for 2 months now. Theres is a slight leak at the cap ( just a few drops) from the container tank, maybe in future they can make the cap from water-tight materials or just do not fill the tank to the brim. Other than that, no major issue.
Universal product so install is up to you to figure out your specific application. Great product, great quality, but really figure out what you need it for. I have this kit installed for when E85 is not available and run ethanol full time. E85 makes more power but the methanol is definitely a huge power upgrade and you will. It be disappointed! Normal driving one gallon of methanol water 50/50 lasts around 1500 miles boost set to start at 10 psi full at 20
Kits works great, I only run water so it serves as a safety feature. I can however notice a difference, my car seems to be consistent with boosting and feels like it has some serious grunt. The only thing I don't get is there seems to be a discrepancy with regards to boost pressures. The AEM is set to come on from 10 PSI but my GFB electronic boost gauge says 7psi, maybe the tap into the boost line is the problem. Either way, works great! Oh and FYI, my AEM comes on at 10 PSI and full at 18 PSI, the water/meth tank supplied seems to last about one and a half full tanks of petrol.
QUESTIONS & ANSWERS
-
Q: 2018 Subaru WRX Alaskan WRX2 years ago
Will this work with my 2018 Subaru WRX and will I be able to mount this in my trunk? Also does this come with everything I need to install?
-
-
0 of
0 people found the
following answer helpful
A: Since this is a universal kit, you may need additional parts to make sure it works 100%. It is common for people to mount this in their trunk.
Michael N.
-
0 of
0 people found the
following answer helpful
-
Q: Nozzle Installation doubt Malammadi6 years ago
Hi, I bought this product and installed it. The manual says to install after the intercooler and maf sensor and before throttle butterfly. The problem I faced was that there was no place to install between the intercooler and throttle body, so I drilled a hole at the bottom end of the intercooler closest to the throttle body and installed the nozzle. I am not sure if that will work or not, can't get hold of my tuner yet so I thought will come back to you
-
-
0 of
0 people found the
following answer helpful
A: That should work, but another common option is sourcing a silicone coupler with a threaded insert in it for installation.
ryanw20299728
-
0 of
0 people found the
following answer helpful
-
Q: wrx 2006 installation Alberto De Santa Anna6 years ago
i have this kit, can i install the pump with conecction looking down? best place to install in a wrx???
-
-
0 of
0 people found the
following answer helpful
A: Gathering information from employees here it just depends on where you have room for it. We have heard of people removing their washer fluid and putting it in the trunk and then putting the pump there in the engine bay. All up to you in the end.
Tommy M. @ RallySport Direct 6 years ago
-
0 of
0 people found the
following answer helpful
-
Q: install! j_currie17617907 years ago
Hi there whats the estimated install time for an experienced Subaru mechanic? thanks!
-
-
0 of
0 people found the
following answer helpful
A: The install time on this kit would be roughly 2-6 hours and that is not including the tuning time afterwards.
guest57853c642a8d25b5018c44a7 @
-
0 of
0 people found the
following answer helpful
This Part Fits
This item is non application specific.
Please verify compatibility before purchase. May require some modification for proper installation.